Aeroworks QB 150cc YAK 55M

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Joe Hunt » Wed Sep 09, 2015 3:36 am

4" TruTurn P51 spinner with lightened backplate and Menz 32-10 cut:

20150908_224656web.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Aeroworks
Posts: 17
Joined: Thu Aug 27, 2015 8:42 am

Re: Aeroworks QB 150cc YAK 55M

Postby Aeroworks » Wed Sep 09, 2015 7:57 am

Looking Good...........Can’t wait for the photoshoot and videos!

User avatar
Naughty Monkey
Posts: 112
Joined: Fri Aug 14, 2015 11:25 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Naughty Monkey » Wed Sep 09, 2015 8:03 am

WTH Nolasco, get with it. Does he need to send monkey over to make sure it gets done? :lol:
Jared


User avatar
Terryscustom
Posts: 14
Joined: Mon Aug 17, 2015 9:59 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Terryscustom » Wed Sep 09, 2015 8:10 am

Very nice! Still digging the scale scheme and lines! But for some reason that tiny spinner on that huge prop made me think of Chris Farley for some reason.
Attachments
1203edfec3c7c2bd976a61de560ba442.500x263x20.gif
flypau.com
mksservousa.com
zdzusa.com

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Joe Hunt » Wed Sep 09, 2015 11:14 am

To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Joe Hunt » Wed Sep 09, 2015 11:14 am

To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Joe Hunt » Wed Sep 09, 2015 11:16 am

To support this site, the reviews, and the photoshoots:

User avatar
Naughty Monkey
Posts: 112
Joined: Fri Aug 14, 2015 11:25 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Naughty Monkey » Wed Sep 09, 2015 11:33 am

Get me down there and i will handle the wardrobe changes and powder any shiny spots that need to be powdered. :D
Jared


User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Joe Hunt » Thu Sep 10, 2015 3:09 am

Got the elevators done. With this setup my servo arm moves 55 degrees each way from the TBD center, so that my elevators move 48 degrees up and down on the AW throw meter. My radio end points are set to 130/130. So, I have pretty much maximum resolution. I used the 1-1/2" hole location on the servo arm because with only one elevator servo per half I wanted to be at least somewhat conservative. I can get more throw, up to 60 degrees or more. But, I'd want to install two more servos for that. We'll see how it goes.

BTW, I worked on my throttle linkage a bit and now my radio end points are set to 135/135 for the throttle servo... max resolution and proportionally linear curve. :)

20150910_000647web.jpg
To support this site, the reviews, and the photoshoots:

User avatar
Joe Hunt
Site Admin
Posts: 392
Joined: Tue Aug 11, 2015 4:21 pm

Re: Aeroworks QB 150cc YAK 55M

Postby Joe Hunt » Thu Sep 10, 2015 3:13 am

I soldered on the PAD to the Dean's connector along with the servo lead:

20150910_000759web.jpg


This grommet works out to be a nice keeper for the elevator extension. I had to remove it, then squeeze it to get the Dean's connector through. Then re-install it. After that the Dean's connector cannot fall back through it. Sweet. :)

20150910_000810web.jpg
To support this site, the reviews, and the photoshoots:


Return to “Build Threads”

Who is online

Users browsing this forum: No registered users and 0 guests